#Sentry gun code
There are three possible ways to unlock and access the safe-by entering its preset Factory Code, your own User Code or a User PIN (Personal Identification Number).
#Sentry gun manual
(See back cover of this manual for your factory code.) Reconnect the keypad by inserting the keypad’s four posts into the matching holes.
#Sentry gun install
Install four alkaline AA batteries as illustrated on the back of the battery holder.
Push up the keypad with your thumbs, and disconnect it from the safe by pulling it towards you. Using two hands, hold the keypad, thumbs down, on its left and right sides.NOTE: Non-alkaline and rechargeable batteries ARE NOT RECOMMENDED. Standard Electronic Lock and Dual Electronic Key Lockįour alkaline AA batteries, Voltage: 6Vdc, (not included) are required to activate the keypad. Gaining Entry into Safes with Electronic Locks With the door closed, turn the handle counterclockwise to secure the locking bolts, then spin the combination dial to the left at least four times to scramble the combination. Stop the FIRST time the pointer reaches the third number of your combination. Stop the SECOND time you reach the second number of your combination. Then stop at the first number of your combination. Make sure ZERO passes the pointer at least THREE times. Test your combination several times with the door open.īefore dialing your combination, simply insert the key (if equipped) in the lock and turn clockwise. DO NOT operate the combination until first reading and understanding the following instructions. IMPORTANT: The lock on this safe is in the open position. NOTE: See the sticker on the back cover of this manual for your combination. Lock instructions Gaining Entry into Safes with Combination Locksģ-Number Combination Lock and Dual Combination Key Lock NOTE: SentrySafe is not responsible for any costs incurred if unit is to be replaced. Place the rubber side of the washer facing down against the safe floor and install the fastener. Assure that the area around the safe hole opening is clean using a damp cloth. If a water resistant unit was purchased, rubberized washers are provided. Place the safe back over the holes and install the fasteners as required.Move the safe away and drill holes of the appropriate diameter and depth for the type of hardware and the mounting surface being used (2 each – bolts, washers and masonry anchors).Note: Fire-Safe models cannot be bolted to the wall. If bolting to a wall, please ensure that the safe is resting firmly on the floor. It is not recommended to attempt to bolt to both floor and wall. Set the safe in place and use the holes provided in the bottom or back of the safe to mark the location of the holes to be drilled in the floor or wall. Select a suitable and convenient location for your safe.To help provide maximum security, SentrySafe strongly recommends this safe be bolted down. Remove the pallet and stand the safe upright on the floor.Tip the safe so that the edge moves to the floor. With your helper, slide safe to one edge of pallet.Close door and put handle in locked position.Once the nuts are removed, use a hammer to tap the bolts through the bottom of the safe.NOTE: If the bolts turn when you begin to remove the nuts, reach between the slats of the pallet and hold the bolts, by hand and/or with pliers, as you turn the nuts. Using a wrench or pliers, remove the nuts located under the X-cut in the carpet in the bottom of the unit.Adjustable wrench, pliers, or 17 mm (11/16”) socket wrench.NOTE: Sentry Group is not responsible for any costs incurred for unit to be removed from pallet and installed in place. Ensure the safe is standing upright on a flat, level surface. Before attempting to unbolt your new safe, be certain someone is with you to help steady the safe while you work. This is a two-person operation and should not be attempted without help. WARNING! UNBOLTING YOUR GUN SAFE FROM THE SHIPPING PALLET! Unbolting your gun safe from the shipping pallet Customer Service representatives are ready to assist you, 8 a.m. If you have any questions about your gun safe, please visit our website at or call Sentry Customer Service at 1-80 or 1-58. Please retain this manual for your records. Writing down a combination and putting it in a desk drawer is like leaving your door key under the mat – it invites entry. Remember to keep your combination a secret.
#Sentry gun full
0 kommentar(er)
